NONLINEAR LATERAL RESPONSE OF PILE GROUP IN CLAY USING THE MODIFIED CAM CLAY SOIL MODEL
DOI:
https://doi.org/10.33736/jcest.4909.2023Keywords:
Lateral displacement, pile spacing, modified Cam clay model, pile group, ultimate loadAbstract
Lateral pile response of the 3 × 3 square pile group has been investigated in terms of lateral displacement and maximum bending moment using three-dimensional finite element analysis. Soil is represented using 8-node isoparametric elements. Piles and pile cap are modelled using 20-node isoparametric elements. The 16-node isoparametric interface elements are used to establish the continuity between the pile and surrounding soil. Soil is represented by the modified Cam clay criterion. The entire code has been developed in FORTRAN 90. The parametric study has been performed to investigate the effect of yield criteria, soil modulus, pile spacing, pile diameter and pile length-to-diameter ratio on the response of the 3 × 3 pile group embedded in clay. A considerable effect of these parameters is observed. It is found that the maximum bending moment in the middle row of the pile group is higher than the front and rear rows for all cases considered in the study. The pile displacement and bending moments in the pile group reduce with an increase in soil modulus, pile spacing and pile diameter. As pile slenderness is increased, it causes an increase in displacement of the pile and a decrease in the maximum bending moment. The modified Cam clay model predicts greater displacements as compared to the Mohr-Coulomb model highlighting the impact of p0 on the yield surface. From the results obtained, the ultimate loads are predicted at a displacement of 5 mm, 10 % of diameter and 20% of diameter.
References
Reese, L. C. (1965). Non-dimensional solution for laterally loaded piles with soil modulus assumed proportional to depth. In Proc. 8th Texas Conf. SMFE. The Univ. of Texas.
Broms, B. B. (1964). Lateral resistance of piles in cohesionless soils. Journal of the soil mechanics and foundations division, 90(3), 123–156.
Sogge, R. L. (1981). Laterally loaded pile design. Journal of the Geotechnical Engineering Division, 107(9), 1179–1199.
Rajashree, S. S., & Sundaravadivelu, R. (1996). Degradation model for one-way cyclic lateral load on piles in soft clay. Computers and Geotechnics, 19(4), 289–300. https://doi.org/10.1016/S0266-352X(96)00008-0
Desai, C. S., & Appel, G. C. (1976). 3-D analysis of laterally loaded structures. In Proceedings of the 2nd international conference on numerical methods in geomechanics, Blacksburg (pp. 405–418).
Yegian, M., & Wright, S. G. (1973). Lateral Soil Resistance Displacement Relationships for Pile Fundation in Soft clays. In Offshore Technology Conference. Offshore Technology Conference. https://doi.org/10.4043/1893-MS
Baguelin, F., & Frank, R. (1980). Theoretical studies of piles using the finite element method. In Numerical methods in offshore piling (pp. 83–91). Thomas Telford Publishing.
Randolph, M. F. (1981). The response of flexible piles to lateral loading. Géotechnique, 31(2), 247–259. https://doi.org/10.1680/geot.1981.31.2.247
Al-Khazaali, M., & Vanapalli, S. K. (2015). Numerical modelling technique to predict the load versus settlement behavior of single piles in unsaturated coarse-grained soils. Proc. of GeoQuébec. https://doi.org/10.13140/RG.2.1.3500.0081
al-Damluji, O. al-F. S., & Al-Anbaki, U. S. (2010). Three-Dimensional Finite Element Analyses of a Single Pile in an Elastoplastic Clayey Soil. Journal of Engineering, 16(3).
Desai, C. S., Alameddine, A. R., & Kuppusamy, T. (1981). Pile cap-pile group-soil interaction. Journal of the Structural Division, 107(5), 817–834.
Desai, C. S., & Abel, J. F. (1971). Introduction to the finite element method; a numerical method for engineering analysis. Van Nostrand Reinhold.
Zaman, M. M., Najjar, Y. M., & Muqtadir, A. (1993). Effects of cap thickness and pile inclination on the response of a pile group foundation by a three-dimensional nonlinear finite element analysis. Computers and Geotechnics, 15(2), 65–86. https://doi.org/10.1016/0266-352X(93)90018-3
Hazzar, L., Karray, M., Bouassida, M., & Hussien, M. N. (2013). Ultimate Lateral Resistance of Piles in Cohesive Soil. DFI Journal - The Journal of the Deep Foundations Institute, 7(1), 59–68. https://doi.org/10.1179/dfi.2013.005
Ilyas, T., Leung, C. F., Chow, Y. K., & Budi, S. S. (2004). Centrifuge Model Study of Laterally Loaded Pile Groups in Clay. Journal of Geotechnical and Geoenvironmental Engineering, 130(3), 274–283. https://doi.org/10.1061/(ASCE)1090-0241(2004)130:3(274)
Chandrasekaran, S. S., Boominathan, A., & Dodagoudar, G. R. (2010). Experimental Investigations on the Behaviour of Pile Groups in Clay Under Lateral Cyclic Loading. Geotechnical and Geological Engineering, 28(5), 603–617. https://doi.org/10.1007/s10706-010-9318-4
Dewaikar, D. M., Verghese, S., Sawant, V. A., & Chore, H. S. (2007). Non-linear 3-D FEA of laterally loaded pile group incorporating no-tension behaviour of soil. Indian Geotech. J, 37(3), 174–189.
Karthigeyan, S., Ramakrishna, V. V. G. S. T., & Rajagopal, K. (2007). Numerical Investigation of the Effect of Vertical Load on the Lateral Response of Piles. Journal of Geotechnical and Geoenvironmental Engineering, 133(5), 512–521. https://doi.org/10.1061/(ASCE)1090-0241(2007)133:5(512)
Abu-Farsakh, M., Souri, A., Voyiadjis, G., & Rosti, F. (2018). Comparison of static lateral behavior of three pile group configurations using three-dimensional finite element modeling. Canadian Geotechnical Journal, 55(1), 107–118. https://doi.org/10.1139/cgj-2017-0077
Halder, A., & Bandyopadhyay, K. (2016). Lateral Load Carrying Capacity Of Piles In Layered Cohesive Soil. In Indian Geotechnical Conference IGC2016 (pp. 15–17).
Yu, Y., Shen, M., & Hsein Juang, C. (2019). Assessing Initial Stiffness Models for Laterally Loaded Piles in Undrained Clay: Robust Design Perspective. Journal of Geotechnical and Geoenvironmental Engineering, 145(10), 04019073. https://doi.org/10.1061/(ASCE)GT.1943-5606.0002074
Li, X.-Y., Wan, J.-H., Zhao, H.-P., & Liu, S.-W. (2021). Three-Dimensional Analysis of Nonlinear Pile–Soil Interaction Responses Using 3D Pile Element Model. International Journal of Geomechanics, 21(8), 04021129. https://doi.org/10.1061/(ASCE)GM.1943-5622.0002076
Luo, R., Zhu, B., & Yang, Z. (2021). Limiting Force Profile for Laterally Loaded Piles in Undrained Clay. International Journal of Geomechanics, 21(8), 04021146. https://doi.org/10.1061/(ASCE)GM.1943-5622.0002066
Potts, D. M., Zdravković, L., Addenbrooke, T. I., Higgins, K. G., & Kovačević, N. (2001). Finite element analysis in geotechnical engineering: application (Vol. 2). Thomas Telford London.
Nayak, G. C., & Zienkiewicz, O. C. (1972). Convenient Form of Stress Invariants for Plasticity. Journal of the Structural Division, 98(4), 949–954. https://doi.org/10.1061/JSDEAG.0003219
Prakash, S. (1962). Behavior of pile groups subjected to lateral loads. University of Illinois at Urbana-Champaign.
Terzaghi, K., Peck, R. B., & Mesri, G. (1996). Soil mechanics in engineering practice. John wiley & sons.
Ismael, N. F., & Klym, T. W. (1978). Behavior of Rigid Piers in Layered Cohesive Soils. Journal of the Geotechnical Engineering Division, 104(8), 1061–1074. https://doi.org/10.1061/AJGEB6.0000678
Standard, I. (1985). Indian standard code of practice for design and construction of pile foundations, part 4: load test on piles. IS.
Congress, I. R. (2016). Standard specifications and code of practice for road bridges. In Indian Roads Congress (pp. 1–89).
Rao, S. N., Ramakrishna, V. G. S. T., & Rao, M. B. (1998). Influence of Rigidity on Laterally Loaded Pile Groups in Marine Clay. Journal of Geotechnical and Geoenvironmental Engineering, 124(6), 542–549. https://doi.org/10.1061/(ASCE)1090-0241(1998)124:6(542)
Downloads
Published
How to Cite
Issue
Section
License
Upon acceptance of an article, the corresponding author on behalf of all authors will be asked to complete and upload the Copyright Transfer Form (refer to Copyright Issues for more information on this) alongside the electronic proof file.
Copyright Transfer Statement for Journal
1) In signing this statement, the author(s) grant UNIMAS Publisher an exclusive license to publish their original research papers. The author(s) also grant UNIMAS Publisher permission to reproduce, recreate, translate, extract or summarize, and to distribute and display in any forms, formats, and media. The author(s) can reuse their papers in their future printed work without first requiring permission from UNIMAS Publisher, provided that the author(s) acknowledge and refer the publication in the Journal.
2) For open-access articles, the author(s) agree that their articles published under UNIMAS Publisher are distributed under the terms of the Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License (CC BY-NC-SA 4.0) which permits unrestricted use, distribution, and reproduction in any medium, for non-commercial purposes, provided the original work of the author(s) is properly cited.
3) For subscription articles, the author(s) agree that UNIMAS Publisher holds the copyright or an exclusive license to publish. Readers or users may view, download, print, and copy the content, for academic purposes, subject to the following conditions of use: (a) any reuse of materials is subjected to permission from UNIMAS Publisher; (b) archived materials may only be used for academic research; (c) archived materials may not be used for commercial purposes, which include but not limited to monetary compensation by means of sale, resale, license, transfer of copyright, loan, etc.; and (d) archived materials may not be re-published in any part, either in print or online.
4) The author(s) are responsible to ensure their submitted work is original and does not infringe any existing copyright, trademark, patent, statutory right, or propriety right of others. The corresponding author has obtained permission from all co-authors prior to submission to the journal. Upon submission of the manuscript, the author(s) agree that no similar work has been or will be submitted or published elsewhere in any language. If the submitted manuscript includes materials from others, the authors have obtained permission from the copyright owners.
5) In signing this statement, the author(s) declare that the researches which they have conducted comply with the current laws of the respective country and UNIMAS Journal Publication Ethics Policy. Any experimentation or research involving humans or the use of animal samples must obtain approval from the Human or Animal Ethics Committee in their respective institutions. The author(s) agree and understand that UNIMAS Publisher is not responsible for any compensational claims or failure caused by the author(s) in fulfilling the above-mentioned requirements. The author(s) must accept the responsibility for releasing their materials upon request by Chief Editor or UNIMAS Publisher.
6) The author(s) should have participated sufficiently in the work and ensured the appropriateness of the content of the article. The author(s) should also agree that they have no commercial attachments (e.g. patent or license arrangement, equity interest, consultancies, etc.) that might pose any conflict of interest with the submitted manuscript. The author(s) also agree to make any relevant materials and data available upon request by the editor(s) or UNIMAS Publisher.
